Zwitterionic Surfactant Modified Carbon Nanotubes Incorporated Percolative Polymer Composites with Improved Features
Farrukh BashirTajamal HussainAdnan MujahidAyesha MushtaqMuhammad Aamir RazaMirza Nadeem AhmadMuhammad ZahidMuhammad Imran DinHuma Tareen
0
Citation
53
Reference
10
Related Paper
Abstract:
Modification of carbon nanotubes (CNTs) and their incoporation in polymer matrix have attracted much attention of researchers. As maximum dispersion of CNTs could enhance the properties of matrix dynamically, researchers are trying to find new methodologies to obtain this target. However, maximum dispersion remains a great challenge and under the stage of progress. Here, we claimed the synthesis of composites with a highly uniform dispersion of the filler that results significantly improved electrical features. In this regard, composites of polymethylmethacrylate (PMMA) were fabricated by using pristine and zwitterionic surfactant (ZIS) modified CNTs (ZIS-CNTs). Characterization was done by using ultraviolet–visible (UV–Vis), Fourier transform infrared (FTIR), X-ray diffraction (XRD), scanning electron microscopy (SEM), and thermo gravimetric analysis (TGA) techniques. UV–Vis and FTIR spectroscopy confirmed the synthesis of ZIS-CNTs and composites. UV–Vis spectra showed an increase in wavelength with the decrease in optical band gap for CNTs-based (CNTs/PMMA) and ZIS-CNTs-based (ZIS-CNTs/PMMA) composites. SEM and XRD studies confirmed a significant homogenoeus and uniform dispersion of CNTs in ZIS-CNTs/PMMA composites. An increase in conductivity of PMMA from 10−9 to 10−2 and 10−1 S/cm was observed on addition of less than 1% (mass fraction) of CNTs without and with modification by ZIS, respectively. Low values of percolation threshold at 0.5% and 0.005% for CNTs/PMMA and ZIS-CNTs/PMMA composites were obtained, respectively. TGA analysis showed a slow rate of decomposition for composites than that for pure PMMA. Around 600 °C, 3% CNTs/PMMA and 7% ZIS-CNTs/PMMA composites were left in the end, which depicts the increase in thermal stability of PMMA. This work depicts a better dispersion of CNTs in PMMA matrix via slight modification in synthesis as well as by using ZIS as surfactant.Keywords:
Thermogravimetric analysis
Aniline monomer coated on the nanotubes in HCl solution was used to prepare a composite of multi-wall carbon nanotube/polyaniline (MWCNT/PANI) by in-situ polymerization. Multi-wall carbon nanotubes were treated by the mixed acid (HNO 3 :H 2 SO 4 in a ratio of 1:3). The content of MWCNT in the samples was 0-20 wt%. The nanocomposites were characterized by Thermogravimetric analysis (TGA), Fourier transform-infrared spectroscopy (FT-IR), Raman spectroscopy and scanning electron microscopy. The mechanical properties of the MWCNT/PANI nanocomposites were also measured. The results showed that the MWCNT was well dispersed in water after purification. Both FT-IR and Raman spectra illustrated the presence of MWCNT in the composites; the interaction between PANI and MWCNT was proved. The Young΄s modulus was 618MPa with 20wt% loading. The effects of treatment of MWCNT on the mechanical properties of MWCNT/PANI nanocomposites are discussed.
Thermogravimetric analysis
In situ polymerization
Cite
Citations (0)
Nanocomposites of hydroxyapatite-fibroin (HA-FB) were prepared using the biomimetic process. The Nanocomposites were detected with X-ray diffraction (XRD), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR) and transmission electron microscopy (TEM). The FTIR results showed that chemical bond forms between HA nanocrystals and fibroin protein. The secondary structure of fibroin can be affected by the mineralization process. TGA results indicated the content of mineralized fibroin in the nanocomposites can be freely adjusted by changing the initial concentration of fibroin solution. TEM image showed that the diameter of the single mineralized nanofibrils is about 2-3 nm and the nanofibrils can aggregate into bundles with the size of 6-8 nm in width and 30-60 nm in length.
Fibroin
Thermogravimetric analysis
Cite
Citations (8)
SiC short fiber(as-received and treated with couple agent) strengthened polytetrafluoroethylene(PTFE) composites were prepared through mixing and cold pressing.The mechanical,friction and wear properties of the composites were tested.The effects of the surface treatment on the performance of the composites were investigated.The fracture surfaces by tensile stress were observed by using a scanning electron microscope(SEM).The strengthen mechanism for the composites was proposed.The results indicated that the tensile strength,impact strength,and friction and wear properties of the composites with surface treated SiC fiber are higher than those with as-received SiC fiber.SEM observation of fracture surfaces showed that poor bonding interface with gaps between untreated SiC fiber and the PTFE matrix is responsible for the lower performances of the corresponding composites.The couple agent surface treated SiC fiber has a strong adhesion with PTFE so that less SiC fiber were pull out during tensile process.
Polytetrafluoroethylene
Cite
Citations (0)
Multiwall carbon nanotube (CNT) reinforced poly(methyl methacrylate) (PMMA) nanocomposites have been successfully fabricated with melt blending. Two melt blending approaches of batch mixing and continuous extrusion have been used and the properties of the derived nanocomposites have been compared. The interaction of PMMA and CNTs, which is crucial to greatly improve the polymer properties, has been physically enhanced by adding a third party of poly(vinylidene fluoride) (PVDF) compatibilizer. It is found that the electrical threshold for both PMMA/CNT and PMMA/PVDF/CNT nanocomposites lies between 0.5 to 1 wt% of CNTs. The thermal and mechanical properties of the nanocomposites increase with CNTs and they are further increased by the addition of PVDF. For 5 wt% CNT reinforced PMMA/PVDF/CNT nanocomposite, the onset of decomposition temperature is about 17 °C higher and elastic modulus is about 19.5% higher than those of neat PMMA. Rheological study also shows that the CNTs incorporated in the PMMA/PVDF/CNT nanocomposites act as physical cross-linkers.
Poly(N-isopropylacrylamide)
Cite
Citations (6)
Abstract We report the synthesis and characterization of a series of conducting poly(2‐chloroaniline) (P2ClAn)/red mud (RM) nanocomposite materials. The polymerization of 2‐chloroaniline in an aqueous medium in the presence of (NH 4 ) 2 S 2 O 8 and RM resulted in the formation of a nanocomposite (P2ClAn/RM). The extent of P2ClAn loading in the composites increased with increasing oxidant and monomer concentrations but decreased with RM. The properties of the nanocomposites were characterized with Fourier transform infrared (FTIR), ultraviolet–visible (UV–vis), conductivity measurements, scanning electron microscopy, thermogravimetric analysis, and differential scanning calorimetry analysis. The inclusion of P2ClAn in the composites was confirmed by FTIR studies. The UV–vis spectra of P2ClAn/RM nanocomposites were similar to that of P2ClAn. The conductivity changed in all the composites prepared under various conditions. Thermogravimetric analyses revealed the enhanced thermal stabilities of the nanocomposites with respect to P2ClAn. Morphological images of the as‐synthesized materials were also investigated with scanning electron microscopy and environmental scanning electron microscopy. © 2005 Wiley Periodicals, Inc. J Appl Polym Sci, 2006
Thermogravimetric analysis
Cite
Citations (10)
Thermogravimetric analysis
Cite
Citations (67)
Thermogravimetric analysis
Thermal Stability
Degradation
Isocyanate
Cite
Citations (169)
Brittleness
Shear Strength
Cite
Citations (1)
Abstract A simple method to fabricate polymer nanocomposites with single‐walled carbon nanotubes is reported, in which the nanotubes were reacted with poly( L ‐lysine) by using high‐speed vibration milling. The nanocomposites obtained were characterized by Fourier transform infrared (FT‐IR), UV–Vis spectroscopy, and thermogravimetric methods. The morphology as well as the dispersion of the carbon nanotubes were determined by scanning and transmission electron microscopy. magnified image
Thermogravimetric analysis
Morphology
Cite
Citations (27)
Thermogravimetric analysis
Polyethylenimine
Matrix (chemical analysis)
Cite
Citations (8)