A Knowledge-Based Advisor for Determination of Limits and Fits
0
Citation
1
Reference
10
Related Paper
This chapter presents an overview of the standardization of rates. We first present some reasons for standardization, and some warnings against its uncritical use. We then define two types of standardization, direct and indirect, and set the stage for a comparison of the two. Later, we present some other methods of standardization, and discuss techniques for standardizing on two correlated dimensions. A problem solving section appears at the end of the chapter.
Section (typography)
Cite
Citations (34)
The authors briefly introduced the importance of standardization,the new trends of standardization in developed countries,as well as the new situation,new tasks and new requirements faced by standardization in China.The main function of the National Technical Committee of Standardization for Wood-based Panels in China was also presented.The authors reviewed the development of standardization for wood-based panels in China and analyzed the main problems existed.Thereafter,necessary actions were suggested to promote standardization for wood-based panels in China,such as to strengthen standardization research,to initiate performance standards,to address public interest standards,to pay more attention to basic methodology standards and to actively participate in international standardization.
Standard system
International standardization
National standard
Technical standard
Cite
Citations (0)
In terms of actual tendency of innovations being the driven part of the world economy development it is necessary to describe the situation with innovations and standardization in Russia. The article is describing Russian innovations eco-system, regulations in innovations and standardization of innovations. Main standardization bodies and challenges in standardization are briefly described. Possible ideas for the development of innovations system in Russia are proposed.
Cite
Citations (0)
Abstract : This study examines the standardization of facility designs. Different levels or degrees of design standardization are identified and defined. The major issues concerning standardization are identified as well as advantages and disadvantages of design standardization. The study recommends that Department of Defense(DoD) adopt a design standardization program that employs a matrix approach. The program recommended would result in an integrated, user-oriented approach to facility design standardization. Keywords: Design standardization, Standard designs, Facility standardization, Computer aided design.
Cite
Citations (0)
The complex standardization has great significance in promoting the standardization work and enhancing the level of standardization. Based on the theory of systems engineering, this paper brings forward complex standardization elements and establishes a general pattern of complex standardization. And then this paper summarizes the typical mode about large aircraft standardization and standardization of circular economy. Finally, the paper proposes some suggestion about applying comprehensive standardized mode in management work.
Mode (computer interface)
Cite
Citations (0)
Starting from the concept of standardization and its the importance,this article analyzed the characteristics of RTA furniture and it's standardization problem.The necessity and urgency to advance the standardization was also pointed out.The contents of standardization with respects to general engineering factors,materials,technological design,quality examination,the comprehensive rank evaluates and so on were disussed with the emphusis of standardization as a key step.Matters needed to be taken into account and strategies during the course of standardization were also discussed.
Rank (graph theory)
Cite
Citations (0)
The problems of standardization of 2D drawings from 3D models in SolidWorks are discussed.The solutions which based on configuration of standardization expression of rolling bearings and gears are presented,and some examples are made to explain role of crop view in standardization drawings.These methods have been applied in enterprises,and have a good effect.
Expression (computer science)
3d model
Cite
Citations (0)
Discussed on standardization problems in the medical devices industry standards on the side of the normative documents,etc. Given some examples of the medical device industry standards in which have some standardization problems exist and proper expressions according with the standardization demands.
Medical device
Standard system
Cite
Citations (0)
Abstract : Results of a 6-month study of standardization criteria & characteristics are presented that may be effectively applied to the Advanced Aircraft Armament System (AAAS) Program. System elements feasibly for standardization are identified. Standardization characteristics for those feasible elements are developed for various levels of standardization (subsystem, module, piece part) and standardization approaches (horizontal, vertical, area, functional, logistical, and cooperative). Alternative standardization characteristics are also postulated and recommendations are formulated for application to the AAAS Program. (Author)
Cite
Citations (0)