SU‐E‐T‐322: The Evaluation of the Gafchromic EBT3 Film in Low Dose 6 MV X‐Ray Beams with Different Scanning Modes
0
Citation
0
Reference
10
Related Paper
Abstract:
Purpose: We have evaluated the response of the Gafchromic EBT3 film in low dose for 6 MV x‐ray beams with two scanning modes, the reflection scanning mode and the transmission scanning mode. Methods: We irradiated the Gafcromic EBT3 film using a 60 degree enhanced dynamic wedge (EDW) with 6 MV x‐ray beams from Clinac iX Linear accelerator (Varian Medical Systems, Palo Alto, CA). The irradiated Gafchromic EBT3 film was scanned with different scanning modes, the reflection scanning mode and the transmission scanning mode. The scanned Gafchromic EBT3 film was analyzed with MATLAB. Results: When 7.2 cGy was irradiated to the Gafchromic EBT3 film, the uncertainty was 0.54 cGy with reflection scanning mode and was 0.88 cGy with transmission scanning mode. When 24 cGy was irradiated to the Gafchromic EBT3 film, the uncertainty was similar to the case of 7.2 cGy irradiation showing 0.51 cGy of uncertainty with reflection scanning mode and 0.87 cGy of uncertainty with transmission scanning mode. The result suggests that the reflection mode should be used in Gafchromic EBT3 film for low irradiation. Conclusion: The result suggests that the reflection mode should be used in Gafchromic EBT3 film for low irradiation.Keywords:
Reflection
Cite
Citations (0)
Vickers hardness test
Functionally graded material
Cite
Citations (31)
Porous SiC Ceramics with Multiple Pore Structure Fabricated via Gelcasting and Solid State Sintering
Porous SiC ceramics with multiple pore structures were fabricated via gelcasting and solid state sintering.A novel gelling agent of Isobam was applied and PMMA was used as both foam stabilizer and pore forming agent.The mechanical properties of porous SiC ceramics were investigated as functions of PMMA content, rotating speed of ball mill, and sintering temperature.With PMMA content increasing from 5wt% to 20wt%, the foaming effect was inhibited while the stability of bubbles increased.When the rotating speed was 220 r/min, the open porosities of the as-prepared SiC ceramics sintered at 2100 varied ℃ from 51.5% to 72.8%, and compressive strength varied from 7.9 to 48.2 MPa.With the rotating speed increasing from 220 to 280 r/min, the foaming effect was aggravated and the porosities of SiC ceramics sintered at 2100 increased.℃ While the sintering temperature increasing from 2050 to 2150 , ℃ the SiC ceramics prepared with PMMA content of 20wt% at rotating speed of 220 r/min decreased in the open porosities while increased in compressive strength.
Cite
Citations (0)
Equiaxed crystals
Cite
Citations (93)
ZrB2 based composites containing 10 vol.-% carbon nanotubes (CNTs) are synthesised by spark plasma sintering at temperatures ranging from 1600 to 18008C and at an applied pressure of 25 MPa. The effects of sintering temperature on densification behaviour, microstructural evolutions and mechanical properties are presented. Results indicate that ZrB2-CNT composites fabricated at 16508C have the optimal combination of dense microstructure and properties. The fracture toughness is sensitive to the temperature change and reaches 7.2 MPa m1/2 for the CNT toughened ZrB2 ceramics, which is higher than the measured result for monolithic ZrB2 (3.3 MPa m1/2). The crack deflection and CNT pullout are the dominant toughening mechanisms.
Spark Plasma Sintering
Toughening
Cite
Citations (6)
Spark Plasma Sintering
Cite
Citations (57)
Relative density
Cite
Citations (15)
Ductility (Earth science)
Cite
Citations (1)
Nanocrystalline material
Cite
Citations (1)