Lightcraft

The Lightcraft is a space- or air-vehicle driven by beam-powered propulsion, the energy source powering the craft being external. It has been theoretically conceptualized by aerospace engineering Leik Myrabo at Rensselaer Polytechnic Institute in 1976, who developed the concept further with working prototypes, funded in the 1980s by the Strategic Defense Initiative organization, and the decade after by the Advanced Concept Division of the US Air Force AFRL, NASA's MFSC and the Lawrence Livermore National Laboratory. The Lightcraft is a space- or air-vehicle driven by beam-powered propulsion, the energy source powering the craft being external. It has been theoretically conceptualized by aerospace engineering Leik Myrabo at Rensselaer Polytechnic Institute in 1976, who developed the concept further with working prototypes, funded in the 1980s by the Strategic Defense Initiative organization, and the decade after by the Advanced Concept Division of the US Air Force AFRL, NASA's MFSC and the Lawrence Livermore National Laboratory. When a Lightcraft is in the atmosphere, air is used as the propellant material (reaction mass). In space, it would need to provide the propellant material from onboard tanks or from an ablative solid. By leaving the vehicle's power source on the ground and by using ambient atmosphere as a reaction mass for much of its ascent, a Lightcraft could potentially be capable of delivering a very large percentage of its launch mass to orbit as an SSTO, an impossible task for chemical rockets. As such, a Lightcraft is distinct from a solar sail because it is dependent on the expansion of reaction mass to accelerate rather than being accelerated by light pressure alone. Within the atmosphere, the Lightcraft propulsion is dependent on the external laser power only, so propulsive power is not limited to that generated by usual on-board machinery (i.e. rockets). First small-scale models used laser propulsion which is a technique still in early stages of development. Lightcraft prototypes are made of solid aluminium machined axisymmetrically. The nose is shaped as a blunted cone for aerodynamical purpose. The rim has an annular air inlet. The aft is a funnel polished as a concave mirror with a pointy tail in the middle extending back out of the body, acting as a parabolic reflector. A ground-based laser aims a high power pulse to the mirror stern. The beam is reflected and focuses to heat the air at an extremely high temperature up to 30,000 degrees, transforming it in a plasma that violently expands, pushing the craft forward. Air is renewed through the inlet and the cycle is repeated at high frequency, acting as an external pulse detonation engine producing thrust. In April 1997, tests by Leik Myrabo in cooperation with the US Army at White Sands Missile Range demonstrated the basic feasibility of propel objects in this way, using a 10-kW ground-based pulsed carbon dioxide laser (1 kJ per pulse, 30 µs pulse at 10 Hz frequency). The test succeeded in reaching over one hundred feet, which compares to Robert Goddard's first test flight of his rocket design. In October 2000, a new flight record was set with a flight lasting 10.5 seconds and reaching 71 meters (233 feet) using the same laser, but this time providing an on-board plastic ablative propellant, and rotating the body around its axis at high speed (over 10,000 rpm) to stabilize the craft with a gyroscopic effect. More advanced concepts of the Lightcraft replace the laser pulses by a microwave beam or maser that can still be ground-based, or alternatively put into orbit, the beams being emitted from above the ascending craft by a series of space-based solar power satellites that could easier keep track of the Lightcraft along its curved ballistic trajectory. The microwave beam detonates the air below the craft exactly like the laser version, but some energy from the beam is also diverted and converted onboard by high-power rectennas into electricity to power an external-flow airbreathing MHD drive called by Myrabo an MHD slipstream accelerator. As an MHD accelerator works only with an electrically conductive medium, some of the incoming microwaves are also diverted within the Lightcraft through a series of transparent windows and mirror sections, then re-emitted in the air near the electrodes of the MHD accelerators located around the rim. The air becomes ionized in these places, allowing MHD interaction of Lorentz forces to actively control the airflow around a discoidal shape that otherwise (i.e. passively) has very bad aerodynamical properties due to its largest surface, a flat plate, being perpendicular to the flow.