x87

x87 is a floating-point-related subset of the x86 architecture instruction set. It originated as an extension of the 8086 instruction set in the form of optional floating-point coprocessors that worked in tandem with corresponding x86 CPUs. These microchips had names ending in '87'. This was also known as the NPX (Numeric Processor eXtension). Like other extensions to the basic instruction set, x87 instructions are not strictly needed to construct working programs, but provide hardware and microcode implementations of common numerical tasks, allowing these tasks to be performed much faster than corresponding machine code routines can. The x87 instruction set includes instructions for basic floating-point operations such as addition, subtraction and comparison, but also for more complex numerical operations, such as the computation of the tangent function and its inverse, for example. Most x86 processors since the Intel 80486 have had these x87 instructions implemented in the main CPU, but the term is sometimes still used to refer to that part of the instruction set. Before x87 instructions were standard in PCs, compilers or programmers had to use rather slow library calls to perform floating-point operations, a method that is still common in (low-cost) embedded systems. The x87 registers form an 8-level deep non-strict stack structure ranging from ST(0) to ST(7) with registers that can be directly accessed by either operand, using an offset relative to the top, as well as pushed and popped. (This scheme may be compared to how a stack frame may be both pushed/popped and indexed.) There are instructions to push, calculate, and pop values on top of this stack; unary operations (FSQRT, FPTAN etc.) then implicitly address the topmost ST(0), while binary operations (FADD, FMUL, FCOM, etc.) implicitly address ST(0) and ST(1). The non-strict stack model also allows binary operations to use ST(0) together with a direct memory operand or with an explicitly specified stack register, ST(x), in a role similar to a traditional accumulator (a combined destination and left operand). This can also be reversed on an instruction-by-instruction basis with ST(0) as the unmodified operand and ST(x) as the destination. Furthermore, the contents in ST(0) can be exchanged with another stack register using an instruction called FXCH ST(x). These properties make the x87 stack usable as seven freely addressable registers plus a dedicated accumulator (or as seven independent accumulators). This is especially applicable on superscalar x86 processors (such as the Pentium of 1993 and later), where these exchange instructions (codes D9C8..D9CFh) are optimized down to a zero clock penalty by using one of the integer paths for FXCH ST(x) in parallel with the FPU instruction. Despite being natural and convenient for human assembly language programmers, some compiler writers have found it complicated to construct automatic code generators that schedule x87 code effectively. Such a stack-based interface potentially can minimize the need to save scratch variables in function calls compared with a register-based interface (although, historically, design issues in the original implementation limited that potential.) The x87 provides single-precision, double-precision and 80-bit double-extended precision binary floating-point arithmetic as per the IEEE 754-1985 standard. By default, the x87 processors all use 80-bit double-extended precision internally (to allow sustained precision over many calculations, see IEEE 754 design rationale). A given sequence of arithmetic operations may thus behave slightly differently compared to a strict single-precision or double-precision IEEE 754 FPU. As this may sometimes be problematic for some semi-numerical calculations written to assume double precision for correct operation, to avoid such problems, the x87 can be configured using a special configuration/status register to automatically round to single or double precision after each operation. Since the introduction of SSE2, the x87 instructions are not as essential as they once were, but remain important as a high-precision scalar unit for numerical calculations sensitive to round-off error and requiring the 64-bit mantissa precision and extended range available in the 80-bit format. Clock cycle counts for examples of typical x87 FPU instructions (only register-register versions shown here). The A...B notation (minimum to maximum) covers timing variations dependent on transient pipeline status and the arithmetic precision chosen (32, 64 or 80 bits); it also includes variations due to numerical cases (such as the number of set bits, zero, etc.). The L → H notation depicts values corresponding to the lowest (L) and the highest (H) maximal clock frequencies that were available.