Voice activity detection

Voice activity detection (VAD), also known as speech activity detection or speech detection, is a technique used in speech processing in which the presence or absence of human speech is detected. The main uses of VAD are in speech coding and speech recognition. It can facilitate speech processing, and can also be used to deactivate some processes during non-speech section of an audio session: it can avoid unnecessary coding/transmission of silence packets in Voice over Internet Protocol applications, saving on computation and on network bandwidth. Voice activity detection (VAD), also known as speech activity detection or speech detection, is a technique used in speech processing in which the presence or absence of human speech is detected. The main uses of VAD are in speech coding and speech recognition. It can facilitate speech processing, and can also be used to deactivate some processes during non-speech section of an audio session: it can avoid unnecessary coding/transmission of silence packets in Voice over Internet Protocol applications, saving on computation and on network bandwidth. VAD is an important enabling technology for a variety of speech-based applications. Therefore, various VAD algorithms have been developed that provide varying features and compromises between latency, sensitivity, accuracy and computational cost. Some VAD algorithms also provide further analysis, for example whether the speech is voiced, unvoiced or sustained. Voice activity detection is usually language independent. It was first investigated for use on time-assignment speech interpolation (TASI) systems. The typical design of a VAD algorithm is as follows: There may be some feedback in this sequence, in which the VAD decision is used to improve the noise estimate in the noise reduction stage, or to adaptively vary the threshold(s). These feedback operations improve the VAD performance in non-stationary noise (i.e. when the noise varies a lot). A representative set of recently published VAD methods formulates the decision rule on a frame by frame basis using instantaneous measures of the divergence distance between speech and noise. The different measures which are used in VAD methods include spectral slope, correlation coefficients, log likelihood ratio, cepstral, weighted cepstral, and modified distance measures. Independently from the choice of VAD algorithm, we must compromise between having voice detected as noise or noise detected as voice (between false positive and false negative). A VAD operating in a mobile phone must be able to detect speech in the presence of a range of very diverse types of acoustic background noise. In these difficult detection conditions it is often preferable that a VAD should fail-safe, indicating speech detected when the decision is in doubt, to lower the chance of losing speech segments. The biggest difficulty in the detection of speech in this environment is the very low signal-to-noise ratios (SNRs) that are encountered. It may be impossible to distinguish between speech and noise using simple level detection techniques when parts of the speech utterance are buried below the noise. For a wide range of applications such as digital mobile radio, Digital Simultaneous Voice and Data (DSVD) or speech storage, it is desirable to provide a discontinuous transmission of speech-coding parameters. Advantages can include lower average power consumption in mobile handsets, higher average bit rate for simultaneous services like data transmission, or a higher capacity on storage chips. However, the improvement depends mainly on the percentage of pauses during speech and the reliability of the VAD used to detect these intervals. On the one hand, it is advantageous to have a low percentage of speech activity. On the other hand, clipping, that is the loss of milliseconds of active speech, should be minimized to preserve quality. This is the crucial problem for a VAD algorithm under heavy noise conditions. One controversial application of VAD is in conjunction with predictive dialers used by telemarketing firms. In order to maximize agent productivity, telemarketing firms set up predictive dialers to call more numbers than they have agents available, knowing most calls will end up in either “Ring – No Answer” or answering machines. When a person answers, they typically speak briefly (“Hello”, “Good evening”, etc.) and then there is a brief period of silence. Answering machine messages usually contain 3–15 seconds of continuous speech. By setting VAD parameters correctly, dialers can determine whether a person or a machine answered the call, and if it's a person, transfer the call to an available agent. If it detects an answering machine, the dialer hangs up. Often, the system correctly detects a person answering the call, but no agent is available. This leaves the called party frustratedly repeating “Hello? Hello?” into the phone, and when combined with the volume of agents that did get through, created the impetus to develop “Do Not Call” lists across the US.