Bimolecular fluorescence complementation

Bimolecular fluorescence complementation (also known as BiFC) is a technology typically used to validate protein interactions. It is based on the association of fluorescent protein fragments that are attached to components of the same macromolecular complex. Proteins that are postulated to interact are fused to unfolded complementary fragments of a fluorescent reporter protein and expressed in live cells. Interaction of these proteins will bring the fluorescent fragments within proximity, allowing the reporter protein to reform in its native three-dimensional structure and emit its fluorescent signal. This fluorescent signal can be detected and located within the cell using an inverted fluorescence microscope that allows imaging of fluorescence in cells. In addition, the intensity of the fluorescence emitted is proportional to the strength of the interaction, with stronger levels of fluorescence indicating close or direct interactions and lower fluorescence levels suggesting interaction within a complex. Therefore, through the visualisation and analysis of the intensity and distribution of fluorescence in these cells, one can identify both the location and interaction partners of proteins of interest. Biochemical complementation was first reported in subtilisin-cleaved bovine pancreatic ribonuclease, then expanded using β-galactosidase mutants that allowed cells to grow on lactose. Recognition of many proteins' ability to spontaneously assemble into functional complexes as well as the ability of protein fragments to assemble as a consequence of the spontaneous functional complex assembly of interaction partners to which they are fused was later reported for ubiquitin fragments in yeast protein interactions. In 2000, Ghosh et al developed a system that allowed a green fluorescent protein (GFP) to be reassembled using an anti-parallel leucine zipper in E. coli cells. This was achieved by dissecting GFP into C- and N-terminal GFP fragments. As the GFP fragment was attached to each leucine zipper by a linker, the heterodimerisation of the anti-parallel leucine zipper resulted in a reconstituted, or re-formed, GFP protein that could be visualised. The successful fluorescent signal indicated that the separate GFP peptide fragments were able to correctly reassemble and achieve tertiary folding. It was, therefore, postulated that using this technique, fragmented GFP could be used to study interaction of protein–protein pairs that have their N–C termini in close proximity. After the demonstration of successful fluorescent protein fragment reconstitution in mammalian cells, Hu et al. described the use of fragmented yellow fluorescent protein (YFP) in the investigation of bZIP and Rel family transcription factor interactions. This was the first report bZIP protein interaction regulation by regions outside of the bZIP domain, regulation of subnuclear localization of the bZIP domains Fos and Jun by their different interacting partners, and modulation of transcriptional activation of bZIP and Rel proteins through mutual interactions. In addition, this study was the first report of an in vivo technique, now known as the bimolecular fluorescence complementation (BiFC) assay, to provide insight into the structural basis of protein complex formation through detection of fluorescence caused by the assembly of fluorescent reporter protein fragments tethered to interacting proteins. Fluorophore activation occurs through an autocatalytic cyclization reaction that occurs after the protein has been folded correctly. This was advanced with the successful reconstitution of the YFP fluorophore from protein fragments that had been fused to interacting proteins within 8 hours of transfection, reported in 2002. There are different production systems that can be used for the fusion protein generated. Transient gene expression is used to identify protein–protein interactions in vivo as well as in subcellular localisation of the BiFC complex. However, one must be cautious against protein over-expression, as this may skew both preferential localisation and the predominant protein complexes formed. Instead, weak promoters, the use of low levels of plasmid DNA in the transfection, and plasmid vectors that do not replicate in mammalian cells should be used to express proteins at or near their endogenous levels to mimic the physiological cellular environment. Also, careful selection of the fluorescent protein is important, as different fluorescent proteins require different cellular environments. For example, GFP can be used in E. coli cells, while YFP is used in mammalian cells. Stable cell lines with the expression vector integrated into its genome allows more stable gene expression in the cell population, resulting in more consistent results.