Chao Yuan

Hunan University

Author Statistics

Papers

Citation

H-Index

i-10 index

Research Trends

Author Order

Document Type

Co-Authors

Jiheng Li

University of Science and Technology Beijing

Xuexu Gao

University of Science and Technology Beijing

Xiaoqian Bao

University of Science and Technology Beijing

Suhua Wang

Guangdong University of Petrochemical Technology

Zhidong Xiao

Huazhong Agricultural University

Wenlan Zhang

Chemnitz University of Technology

Jinquan Li

Huazhong Agricultural University

Jie Zhu

Yulin University

Chengfei Li

Air Force Medical University

Yu Jin

East China University of Science and Technology

Cooperative Institutions

Huazhong Agricultural University

Chinese Academy of Sciences

Soochow University

University of Science and Technology Beijing

Guangdong University of Petrochemical Technology

General Research Institute for Nonferrous Metals (China)

Sichuan University

North China Electric Power University

Grinm Advanced Materials (China)

Nanjing University

Author Statistics

Papers

Citation

H-Index

i-10 index

Research Field

A sensitive polymer dots fluorescent sensor for determination of α-L-fucosidase activity in human serum

Sensors and Actuators B Chemical (2019)

Cheng Xin Yan Huang Diying Li Chao Yuan Zilong Li

Quantum yield

10.1016/j.snb.2019.02.076

Cite

Citations (16)

Development of alumina primary coat for single crystal investment casting ceramic mould

British Ceramic Transactions (2002)

Chao Yuan S. Jones Paul Withey P. M. Marquis

The use of an alumina primary coat to eliminate the interaction between aluminium in NiAl single crystal alloy and silica in the ceramic investment casting mould has been examined in this study. The properties of the alumina slurry were characterised and the main factors controlling stability identified. It was found that the pH of the slurry must be carefully controlled to avoid polycondensation reactions. The most stable slurry was produced using filler with lower mean particle size and alkalinity. Alumina primary coat produced with low filler loading does not survive completely during wax removal. The surface condition can be improved by increasing the plate weight, which corresponds to a higher filler loading in the slurry. Moulds with a consistent alumina primary coat exhibit slightly higher green and sintered strength than moulds with the standard zircon-silica primary coat.

Investment casting

Filler (materials)

Alkalinity

10.1179/096797801225000842

Cite

Citations (6)

Water-soluble single molecular probe for simultaneous detection of viscosity and hydrazine

Spectrochimica Acta Part A Molecular and Biomolecular Spectroscopy (2023)

Yu Jin Ruitao Sun Guangqiang Li Mi Yuan Weichong Shao

Hydrazine (antidepressant)

10.1016/j.saa.2023.122558

Cite

Citations (9)

Metal-organic frameworks-based broad-spectrum sensor for total tetracycline antibiotics assay

Dyes and Pigments (2022)

Hongxia Chen Junyu Chen Chao Yuan Long Yu Mingtai Sun

Tetracycline antibiotics

Chlortetracycline

10.1016/j.dyepig.2022.110887

Cite

Citations (12)

Bioorthogonal chemistry-based high-efficient quantum dots binding boosts the detection sensitivity of plasmon-enhanced fluorescence platform for immunoassay

Sensors and Actuators B Chemical (2023)

Xiaohong Min Benmei Cao Song Huang Chao Yuan Suhua Wang

Bioorthogonal Chemistry

Avidin

10.1016/j.snb.2023.133516

Cite

Citations (4)

Single microbead-based fluorescence “turn on” detection of biothiols by flow cytometry

Talanta (2018)

Ahmed Mohamed Xuemeng Li Jinquan Li Chuangye Lin Abdullah M. Asiri

Microbead (research)

10.1016/j.talanta.2018.11.025

Cite

Citations (8)

Magnetostriction properties of oriented polycrystalline CoFe 2 O 4

Journal of Magnetism and Magnetic Materials (2015)

Jiquan Wang Xuexu Gao Chao Yuan Jiheng Li Xiaoqian Bao

Polyvinyl Alcohol

10.1016/j.jmmm.2015.10.073

Cite

Citations (34)

Immunogenicity and protective capacity of EF-Tu and FtsZ of Streptococcus suis serotype 2 against lethal infection

Vaccine (2018)

Liping Feng Xiaona Niu Wen Mei Weitian Li Yuan Liu

Streptococcus suis

10.1016/j.vaccine.2018.03.079

Cite

Citations (17)

Effect of incorporation of zirconia layer upon physical and mechanical properties of investment casting ceramic shell

Materials Science and Technology (2012)

Chao Yuan Paul Withey S. Blackburn

Post-heat treatment recrystallisation is a significant cause of scrap in single crystal component production. This defect could be prevented by a reduction in the mechanical strength of the shell after the metal has solidified. Addition of a zirconia layer, to produce large cracks around grain boundaries and among the large grains during phase transformations, was considered as a method of reducing sintered strength. In this study, two types of zirconia stucco, monoclinic and partially stabilised, were introduced into the shell. The effect of the incorporation of a zirconia layer on the microstructure and mechanical properties of the shell were investigated. Shell with a monoclinic zirconia additional layer showed no reduction in the green strength but a better performance in high temperature deformation tolerance, maintaining shell performance during wax removal and metal casting. The shell strength after alloy solidification is reduced, suggesting that a reduction in recrystallisation may be possible with this method.

Monoclinic crystal system

10.1179/1743284712y.0000000076

Cite

Citations (9)

Effect of hot isostatic pressing on microstructure of cast gas-turbine vanes of K452 alloy

Progress in Natural Science Materials International (2014)

Jie Li Chao Yuan Jianting Guo Jieshan Hou Lanzhang Zhou

The effect of hot isostatic pressing (HIP) treatment on microstructure of gas-turbine vanes made of K452 alloy was investigated by OM, SEM and TEM. The results showed that HIP treatment played a great role in the porosity healing processing, where 80% of porosities were eliminated and the diameter of remnant porosities decreased to 10 μm. The healing mechanism of the porosities was consistent with existing theories of porosity closure based on vacancy diffusion. According to the result of the tensile test, the plasticity of the alloy was improved as the result of the elimination of the porosities and the improvement of dendritic segregation, while there was not an obvious improvement in the tensile strength after the programmed HIP process. In addition, HIP had a positive effect on narrowing down the dispersion of tensile properties.

Hot isostatic pressing

10.1016/j.pnsc.2014.10.008

Cite

Citations (24)