Template-directed electrodeposition was utilized to fabricate FexPd1-x nanowires where the dimension was controlled by template pore size (i.e., 30 and 200 nm) whereas the composition was tuned by varying the Fe+2/Pd+2 metal ion ratio in ammonium chloride baths at fixed deposition current density of 5 mA cm−2. A wide range of composition (i.e., Pd-rich, near equiatomic, and Fe-rich) were successfully fabricated and their magnetic properties were examined. Additionally, single nanowire was also integrated on to microfabricated gold electrodes by magnetic alignment, followed by post-annealing in a reducing environment to make good electrical contacts. Assembled single nanowire was utilized to determine their electrical transport properties including temperature-dependent resistance (TCR) and magnetoresistance (MR). Additionally, the feasibility of FexPd1-x nanowire based hydrogen sensor was examined at room temperature.
In this study, the effect of heat treatment on the fracture behavior of alloy B steel with boron (B) contents as high as 130 ppm was investigated. The Alloy B are derived from Gr.92 steel with outstanding creep characteristics. The amounts of minor alloying elements such as B, N, Nb, Ta, and C were optimized to achieve better mechanical properties at high temperatures. Hence, workability of the alloy B and Gr.92 were compared. An increase in the B content affected the phase transformation temperature and texture of the steel. The development of the {111}<uvw> components in γ-fibers depended on the austenite fraction of the steel after the phase transformation. An increase in the B content of the steel increased its α-to-γ phase transformation temperature, thus preventing the occurrence of sufficient transformation under the normalizing condition. Cracks occurred at the point of the elastic-to-plastic deformation transition in the normal direction during the rolling process, thereby resulting in failure. Therefore, it is necessary to avoid intermediate heat treatment conditions, in which γ-fibers do not fully develop, i.e., to avoid an imperfect normalization.
PURPOSE Osteosarcoma occurring in the head and neck region is known as a malignant tumor that shows a relatively poor prognosis and, despite various treatments, clinicians have often been confounded by it. The existence or non-existence of the mutation of the gene p16 INK4a has been used in prognosis assessment. In this study, author have attempted to determine whether methylation of the gene p16 INK4a could be applied to forecast the progress of osteosarcomas in the head and neck region having been given poor prognoses in the diagnostic process and the early stage of treatment. RESEARCH SUBJECT AND METHOD Clinicopathologic investigations, immunohistochemical examinations, a methylation specific polymerase reaction (MSP) analysis, and a survival analysis were conducted on the tissues of 20 patients with mandibulofacial osteosarcoma. RESULTS Neither age, sex, size, smoking or non-smoking, nor region have showed a statistical significance with methylation or unmethylation of the gene p16 INK4a and expression rates demonstrated by immunohisto- chemical examinations. A chi-square test indicated that recurrence inclination has no relation with the expression rate of p16 protein (p=0.6615), but it showed a statistical significance with methylation of the gene p16 INK4a (p=0.0033). With respect to investigations of the survival rates, a Kaplan-Meier survival analysis found that the manifestation rate of p16 protein did not have an impact on survival (p=0.8864), but that the methylation of the gene p16 INK4a resulted in significant differences in survival rates (p=0.0105). CONCLUSIONS The above results show that methylation of the gene p16 INK4a could be one of the major factors that help determine the recurrence inclination and prognosis of osteosarcomas occurring in the head and neck region.
In this study, the effect of heat treatment was investigated to influence the occurrence of fracture during manufacturing process of Alloy B steel with boron contents as high as 130 ppm. As the content of boron increases, it affects the phase transformation temperature and texture. The development of {111}<uvw> components in the γ-fiber is affected depending on the austenite fraction after phase transformation. The Alloy B steel indicated that the increase in the boron content increased the α to γ phase transformation temperature such that sufficient transformation did not occur in the normalizing condition. The cracks occurred at the point of the transition from elastic to plastic deformation in the ND direction during the rolling process, thereby resulting in failure. Therefore, it is necessary to avoid the intermediate heat treatment condition in which γ-fiber does not fully develop, i.e., an imperfect normalization.
Maxillary deficiency, anterior cross bite, constriction of maxillary arch, malaligned teeth are frequently observed in patients with cleft lip and palate. Surgery and orthodontics, combined intervention are needed to correct maxillary deficiency. Distraction osteogenesis that currently used has many advantages like less relapse tendency, more advancement of maxilla, capable in growing patients. In case 1, 18 years old girl with BCLP had severe midfacial deficiency and multiple missing of teeth. LeFort I osteotomy, followed by maxillary distraction osteogenesis utilizing rigid external distraction device(RED) system, was performed. After a 6-day latency period, distraction proceeded at a rate of 1mm per day (at 1st week, 1.5mm/day). Total advancement was 19mm. The RED device left in place for the additional 4 weeks for consolidation. After the RED device was removed, face mask was applied with elastic traction for 5 weeks. After achieving acceptable facial appearance and occlusion, orthodontic appliance was removed. The results after 4 years follow-up was sustained pretty well without aggravation of velopharyngeal function. In case 2, 22 years old man with UCLP had severe midfacial deficiency and palatally erupted upper 2nd premolars due to arch length discrepancy, but the anterior segment of maxillary did not show constriction and crowding. patient had no arch width discrepancy, crowding was concentrated on premolar region. Segmental LeFort I osteotomy was performed. After a 6 - day latency period, using internal distraction device, distraction proceeded at a 0.5mm per day(at 1st week, 0.75 - 1 mm/day). Total advancement was 15mm. After internal distraction device was removed, face mask was applied with elastic traction for 4 weeks. After surgical-orthodontic treatment, facial appearance and occlusion was improved pretty good, and after 46 months follow-up the result was retained well.
'%3e%3cg id='b'%3e%3cpath id='a' stroke='%23000' stroke-width='2' d='M-6-25H6m-12 3H6m-12 3H6'/%3e%3cuse xlink:href='%23a' y='44'/%3e%3c/g%3e%3cpath stroke='%23fff' d='M0 17v10'/%3e%3ccircle r='12' fill='%23cd2e3a'/%3e%3cpath fill='%230047a0' d='M0-12A6 6 0 0 0 0 0a6 6 0 0 1 0 12 12 12 0 0 1 0-24z'/%3e%3c/g%3e%3cg transform='rotate(-123.69)'%3e%3cuse xlink:href='%23b'/%3e%3cpath stroke='%23fff' d='M0-23.5v3M0 17v3.5m0 3v3'/%3e%3c/g%3e%3c/svg%3e)
